advanced poly packaging t-1000 manual

To supplement manuals, Advanced Poly also offers Technical Assistance in our Help section where other “How-To” documents downloads are provided to assist your maintenance personnel. You may not copy this manual in whole or part without the consent of Advanced Poly-Packaging, Inc. All information pertaining to the promotion, sale, distribution, operation and maintenance of the T-1000-S14 ADVANCED POLY-BAGGER including this manual, drawings, schematic, wiring diagrams, VHS video tapes, brochures, specification sheets, figures, charts, or any other information, due to its proprietary design and manufacture remain the property of Advanced Poly Packaging, Inc. Once the work order is complete or the container is full, the T-1000-S14 stops to alert the operator to begin the next work order or to push aside the box and begin filling another. Pressing anywhere on the screen resets the counter and starts the bagging operation with minimum delay. The offline printer is mounted. Small, lightweight and equipped with castors, use this conveyor anywhere in the plant.Additionally, this chapter describes safety precautions, how to power on the T-1000-S14 and how to properly thread bags through the machine. It is shipped completely assembled except for a few items that are easily attached during installation. Unless physically damaged, the T-1000-S14 will function properly after minor adjustments are made. This tubing affixes to the coupler adapter (quick disconnect not provided). Connect the air to the regulator by holding the regulator firmly in one hand and pushing the airline connector on the male regulator connector. CAUTION: If the bagger is not held in position by two people, the weight of the machine may cause it to drop suddenly, causing severe injury. See Figure 2-3. To turn the T-1000-S14 on, turn the switch counterclockwise from its vertical OFF position to its horizontal ON position.

• advanced poly packaging t-1000 manual, advanced poly packaging t-1000 manual, advanced poly packaging t 1000 manual pdf, advanced poly packaging t-1000 manual download, advanced poly packaging t-1000 manual pdf, advanced poly packaging t-1000 manual free, advanced poly packaging t-1000 manual instructions, advanced poly packaging t 1000 manual pdf.

You must have JavaScript enabled in your browser to utilize the functionality of this website. This version applies to Model T-1000 Serial Numbers from 218121484 - current. This version applies to Model T-1000 Serial Numbers from 218121484 - current. This version applies to Model T-1000 Serial Numbers from 95080001 - 201010430. This version applies to Model T-1000 Serial Numbers from 95080001 - 201010430. This version applies to Model T-1000 Serial Numbers from 213101186 - 214101246 This version applies to Model T-1000 Serial Numbers from 213101186 - 214101246 This version applies to Model T-1000 Serial Numbers from 215051292 - 215091303. This version applies to Model T-1000 Serial Numbers from 215051292 - 215091303. This version applies to Model T-1000 Serial Numbers from 215101304 - 216021321. This version applies to Model T-1000 Serial Numbers from 215101304 - 216021321. This version applies to Model T-1000 Serial Numbers from 216031322 - 217041390. This version applies to Model T-1000 Serial Numbers from 216031322 - 217041390. This version applies to Model T-1000 Serial Numbers from 217041391 - 217121413. This version applies to Model T-1000 Serial Numbers from 217041391 - 217121413. This version applies to Model T-1000 Serial Numbers from 217121414 - 218011427. This version applies to Model T-1000 Serial Numbers from 217121414 - 218011427. This version applies to Model T-1000 Serial Numbers from 218011428 - 218121483. This version applies to Model T-1000 Serial Numbers from 218011428 - 218121483. However, sometimes there is a lag between the release of the technical data and shipment of the system causing incorrect information in the manuals. These changes may actually be present in later releases.It is our goal to continuously improve our technical documents and we offer free document downloads to all users. For an extra copy of the printed document there is a charge for printing and document preparation.

See Figure 3 - 24. DF-20 Part Diverter (Diverting Funnel) This feature is used to count bags and divert them from the. The Pressure Sensor may also be added to the T-1000 to validate only pressure, without adding the other two components. For application requiring this validation only, the bagger will not operate unless the sensor provides an output indicated that the pressure is above a minimum allowable setting. If the T-1000-S14 is running in Manual Mode, a warning screen will be displayed, and the operator will have the option to reprint the label from that screen. Since variables such as position and age of the thermocouples may affect the actual reading, a calibrated readout will provide for more consistency in sealing. See section 3.37 for “Pass Code Setup”. Several menu options are available from the Tech Assist. Menu which will assist with troubleshooting the T-1000- S14 and also change settings that affect the operation of the equipment. When equipment is shipped, APPI uses the following codes which should be changed prior to putting the T-1000 into operation. Factory Set Pass Codes: 1. Level 1 pass code: 1001 2. Level 2 pass code: 1002 To enable the pass code function, press the. This delay setting allows the bag to get into position before blowing it open. To change this setting, press the button, enter a value on the numeric keypad and press the button. Brightness Control. Touch the button to access the Bagger Factory screen. From there touch the button located along the right-hand side of the screen. Go to Settings and set the specifications for your job. Once the job is set, touch on the right side of the screen to access the Bagger Job Save screen, see Figure 3 - 43. Touching the QTY box will access a green numeric keypad where the operator can enter the number of products that will go into each bag. For instance, if three items go into the bag before it is sealed, the number 3 can be entered into that field.

The green Power light on the touch screen will illuminate and the Introduction screen will be displayed. One bag should index, blow open and stop between the pressure bar and the heater bar.See Figure 3 - 1. The Introduction screen is a welcome screen, and it contains a button that will take the operator to the Operation screen. When turned on, the. If the pass code function is enabled in the Technical Assistance Screen, the touch screen will default to the Operation Screen after a preset time has elapsed. In the Manual mode with NO accumulating funnel, Fill Time will delay the operation from starting until this time has passed. Options Menu Options that have been added to the T-1000 at the factory can be setup from the Options Screen.Once the mechanical adjustment is complete, press and for normal operation of the flat seal assembly. In the Auto mode, the option will operate automatically. This option is useful to segregate different parts or protect damage caused from part contact. See Figure 3 - To start, set the First Seal Point by pressing the. See Figure 3 - 13. To turn ON the option, press the toggle button to ON. Press the button to reset the count to the pre-set value. BO Cycle button allows you to test cycle the Bag Opening Device alone, without initiating other equipment or the T-1000 seal operation. LC-10 Light Curtain This option is used as a safety device to disable air power when the active area is obstructed. The Light Curtain option can be used as a means of initiating the cycle operation of the T-1000. To cycle the bagger automatically after the light curtain sensing area is cleared, press the toggle button to change from Safe to Auto. AF-10 Accumulating Funnel. ES-10 E-Stop Circuit This option can be used to stop the cycle operation of the T-1000 and possibly other auxiliary infeed or out-feed equipment. One or more Estop buttons may be equipped. To adjust the height, toggle the Option ON and press the UP Arrow or the DOWN Arrow.

If there are signs of wear and tear it must be replaced. Wires should not extend past the end of the heater bar. Note: If the wires rub on the bagger when the heater bar is in or out, the heater cartridge will fall prematurely. Preventative Maintenance and Scheduled Maintenance To extend the life of the T-1000-S14, qualified maintenance personnel must perform all required maintenance tasks. Failure to perform scheduled and preventative maintenance may cause excessive wear to components and will void the warranty. Blue (33M Roll) 10 ft. TP-406181 Filter, 4 Micron (Air Knife) Plate TP-T1MB00010. When operating difficulties occur, the best procedure is to observe what is happening, identify the causes and effect the correction. Make only one adjustment at a time, checking the results of each adjustment. Card: Address Description Normal State Inputs Main PLC Reserved for Stepper control Main PLC Perf Sensor Main PLC Not Used - Available. Piping from Solenoid Valve Stations 5 through 11 will change based on the configuration of the T-1000 and the options ordered by the customer. See Dwgs T- 1000 PNE 1 through 7. PART No DESCRIPTION TA-T10240-IOP SEVEN INCH TOUCH SCREEN TP-T1MD00109 MOUNTING BAR TP-111215 JOINING TEE TP-T1MD00094 BASE TELESCOPE TP-111104 COLLAR CLAMP TP-T1MA00088 BASE CLAMP PIPE. Please note this when ordering parts from the Bill of Materials shown above. For example, a Bagger with a 6.25” Pass-Through will use Seal Guide Rod TP-T1MB00033-W18-2, Shield Mounting Rod TP-T1MB00144-2, and Main Cylinder TP-403242. This manual and the program operating the equipment described in it are copyrighted. You may not copy this manual in whole or. Where labor reduction and fast changeover is important, the T-1000 uses Advanced Poly-Bags (pre-opened bags on rolls), manufactured by Advanced Poly-Packaging, Inc. Estop - This option can be used to stop the cycle operation of the T-1000 and possibly other auxiliary infeed or outfeed equipment if purchased with the T-1000.

Contains the information required for operation of the Program File, organized by data type. Figure 3 - 49 External Storage The Memory Stick contains several types of data from the machine. The Bagger Settings are stored, similar to the information in PLC Storage. This is because the files are hidden to prevent damage, and therefore do not show up in Windows Explorer. Do not store any information in these files as it will alter the program and will not function when the memory stick is re-inserted in the touch screen. However, these files must be saved (copied) to a PC without the original file changed. Then, the files can be used and saved as MS Excel files for full use of the MS Excel formulas. When shipped from the factory, a 60-day trial activation is included. After full payment for the software is received, a full software license will be granted. See Figure 3 - 58 and Figure 3 - 59. Press the button once to reset the production time and twice to reset the graph. Figure 3 - 58 Figure 3 - 59 Operation Mode Timers,. See Figure 3 - 62. Figure 3 - 62 Warning and Message Screens Normal operating message and fault messages will be displayed automatically to alert the operator of situations on the machine. Note: A light source (lamp) positioned to the rear of the T-1000-S14 showing light in the gap of the rollers will assist in judging whether the upper and lower roller are parallel. To order a replacement Teflon Sheet, call APPI Service and refer to part number TP-300500, T-1000 Teflon Sheet. 1. Turn the power to the OFF position and unplug the power cord. Let machine cool for at least an hour. Pressure Bar Adjustment The pressure bar, when actuated by the seal cylinder, is forced against the front plate. The pressure bar must be parallel to the front plate to avoid excessive wear of components. Put the T-1000 in Auto Run and let it cycle.Check the cable for any cuts or worn spots that could be going to ground.

When the button is pressed, a screen will appear indicating this condition. 3.41 UF-5000 Infeed Conveyor Settings Screen The UF-5000 settings screen provides all the settings to control production speeds and timing of the integration components of a system. To disable the option, set the value to zero. Note: If you don’t want the bags separated ever, you can either set the counter value to very large number or simply change the Reverse setting to zero in the Bag Setup Menu. See Figure 3-69. If the temperature is out of this ranging a Warning signal will display Feed Dist- displays a distance in inches where perforation sensor is not looking for a perforation.. Options must be purchased from Advanced Poly-Packaging, Inc.Contact Advanced Poly-Packaging, Inc. Service Dept. for more information regarding options available for the T-1000. Occasionally, reprogramming will be necessary to interface auxiliary (infeed) equipment that is not manufacturer by APPI. Adjustments may be required after transportation, excessive handling, or due to normal wear and tear.If the variance is too great, a Feed Error message with be displayed. Note: Feed errors are detected and displayed on the screen. Once a feed error occurs, the bagger will restart to calculate the bag length. 3.13 Seal Time Displays, in seconds, the time the pressure (rubber) bar will remain touching the surface of the bag for proper sealing. Then re-tighten the nut on the adjustment screws. Replace the covers, plug the cord into the power outlet and turn the main power on. 4.4 Dancer Assembly Adjustments (Roller Shaft) A roller shaft, holding in position a roll of bags, will rest on the side-plates of the dancer assembly. The roller shaft must be parallel to the upper and lower guide rollers to allow proper tracking through the center of the T-1000. The Teflon should periodically be inspected for wear or damage.

If holes or tears exist, the Teflon rolls can be turned (rotated) to cover the contact surfaces with fresh Teflon. If a change of Teflon is required, turn the main power to the OFF position and unplug the power cord. To decrease the speed of the pressure bar INWARD, turn the knob (B) clockwise. To increase the speed of the pressure bar OUTWARD, turn the knob (A) counter clockwise. To decrease the speed of the pressure bar OUTWARD, turn the knob (A) clockwise. Then, standing in front of the T-1000, push the pressure bar slowly towards the front plate, keeping hands and fingers out of the seal area. While pushing the pressure bar towards the front plate do not compress the rubber into the nylon holder or touch the round nuts on the pressure bar (Fig. To replace the heater cartridge, turn the main power to the OFF position, unplug the power cord and disconnect the air line. Disconnect the heater cartridge wire at the connector. From underneath the inner frame, loosen and remove the screws which holds the wire clamp and lower heater bar plate to the upper heater bar plate (Fig. Bill of Materials Top Level Report (see Drawing No. Description TA-T10100-S14 Head Assembly, T-1000-S14 TA-T10199 Stand Assy,T-1000 TA-T10240 IOP Control Case Assy. Bill of Materials Top Level Report (see Drawing No. Description TA-T10018 Flat Load Shelf Sub-Assembly TA-T10110-S14 Main Frame Assy, TA-T1000-S14 TO-T1-FU-MISC Additional Funnel for T-1000 TP-T1MD00044 Top Cover. Bill of Materials Top Level Report (see Drawing No.Bill of Materials Top Level Report (see Drawing No. Description TA-T10250-S14 Main Frame Assy, T-1000-S14 TA-T10270-S14 Electrical Panel, T-1000-S14 TA-T10280-S14 Sealer Frame Assy, T-1000-S14. Bill of Materials Top Level Report (see Drawing No. Description TA-T10001-S14 Air Knife Assy. T-T1000-S14 TA-T10002-S14 Upper Roller Assembly TP-T1MC00001S14 Main Side Plates, T-1000-S14 TP-T1MC00017 Vulcanized Rubber Roller. Bill of Materials Top Level Report (see Drawing No.

CF-10 Counting Funnel -This option is useful to automatically cycle the bagger when a preset number of parts have fallen through the funnel. Other options may have been added since the date this list was printed. Please call for additional or Custom options pricing. Additionally, this chapter describes how to turn on power to the T-1000 and properly thread bags through the machine. 2.1 Installation Procedures The T-1000 is transported as a single unit in a custom crate designed to protect the machine during shipment. After the removal of the strapping, the dancer should be checked to make sure that it will rotate freely in a semicircular path. The shaft assembly may then be inserted into the dancer frame brackets so it is over the brake stop for tension. Insert the right side of the roll shaft in the right side of the shaft holder (circular holder). Unless physically damaged, the T-1000 will function properly after minor adjustments are accomplished. Read Chapter 4 for information on adjustments of the T-1000. The Introduction screen is a welcome screen and has a button to take you to the Operations Menu. See Figure 3-1 3.7 Operation Screen The Operation Screen is provided to function with Pass code Protection function of the machine. If the pass code function is enabled in the Technical Assistance Screen, the touch screen will default to the Operation Screen after a preset time has elapsed. When the T-1000 is equipped with an accumulating funnel, Fill Time will affect the delay time before sealing, after the door has closed on the accumulating funnel. 2) In the AUTO cycle mode with no auxiliary infeed equipment, Fill Time affects the paced rate operation. Note: As an additional seal function, cool time may also be required for heavy or bulky products. If too hot, the seal may separate when the pressure bar releases the bag after sealing.

The fingers enter the bag immediately before the pressure bar presses the two layers of the bag together, against the front sealer plate. This option is used as a safety device to avoid personal injury by ensuring that fingers or hands are not in the seal area during the cycle operation of the T-1000. See Figures 3-13 thru 3-15. The message tells the operator that the machine will automatically cycle when they remove their hands. Caution: To avoid personal injury, do not attempt to disable the Light Curtain option unless a funnel is added which physically blocks the path to the heater bar. Toggle switch to or to disable the operation of the printer. See Figures 3-26-3-28. 3.27 CF-10 Counting Funnel A Photo optic and preset Counting option not included in the standard T-1000 package and must be purchased separately. In a manual operation, the operator can insert the product into the funnel without waiting for the bag to be in position and opened. When the bagger is ready to receive the product, the door at the bottom of the funnel will open, drop the product and shut, to allow the funnel to again be loaded. This option is not included in the standard T-1000 package and must be purchased separately. For instance, it may be necessary to segregate a sharper object (screw) from a plastic component (mounting plate) to avoid the screw damaging the plastic part. For application requiring this validation only, the bagger will not operate unless the sensor provides an output indicated that the pressure is above a minimum allowable setting. 3.35 BV-10 Barcode Reader Option As an optional device, a barcode reader can be purchased from APPI to verify that a barcode is readable. A typical value is.2 seconds. is a delay time before the finger will attempt to enter the bag, after it is initially blown open. A typical value is.5 seconds. The UF-5000 is equipped with an emergency stop (ESTOP) switch, either a push button or pull cord.

T-T1000-S14 Item Item No.Description TC-T1000-S14 Harness, T-1000-S14 Stepper TP-T1MC00002S14 Angle Mnt-5 Phase Driver T-1000-S14 TP-T1MC00016S14 Electronics Mtg. Bracket-T-1000-S14 TP-T1MC00006S14. Description TA-T10025-S14 Pneumatic Mtg. Valve Assy. S-14 TP-403244 Cylinder, NCQ2A4OUIA950549 T-1000 TA-T10005 Pressure Bar Sub-Assembly. Bill of Materials Top Level Report (see Drawing No. Description TP-T1MB00029 Anti-Jam Pressure Housing TP-T1MB00030 Anti-jam Contact Center Strip TP-T1MB00031 Anti-jam Pressure Pad TP-T1MB00068 Anti-jam Contact Strip. Description TP-T1MB00008 Heater Bar Mtg Plate TP-T1MB00009 Heater Seal Bar - Both Halves TP-T1MB00024 Heater Cartridge Corner Hanger. Bill of Materials Top Level Report (see Drawing No.Bill of Materials Top Level Report (see Drawing No. Description TP-T1MB00004 Grooved Metal Roller Mounting Block TP-T1MB00012 Grooved Lower Roller (Steel) TP-T1MB00013 Grooved Lower Roller Shaft. Bill of Materials Top Level Report (see Drawing No. Description TA-T100124-3 Grounding Sensor TP-T1MB00028 Grooved Metal Roller Finger TP-T1ME00325 Grounding Sensor Wire Assembly TP-101102 Nut,6-32 Hex Mach Screw Pltd. Bill of Materials Top Level Report for (see Drawing No. Description TP-T1MB00060 Latch TP-T1MB00061 Latch cam TP-106135 Dowel Pin. Bill of Materials Top Level Report (see Drawing No.Bill of Materials Top Level Report (see Drawing No. Description TP-T1MA00087 Cross Pipe Weldment TP-T1MC00019-1 Base Clamp Block (Left) TP-T1MC00019-2 Base Clamp Block (Right) TP-101105 Jam-nut 10-32. Bill of Materials Top Level Report (see Drawing No. Description TA-T10010 Film Tension Hub Sub-Assembly TA-T10011 Dancer Guide Sub-Assembly TP-T1MA00069-1 Dancer Side Frame Plate (Left) TP-T1MA00069-2 Dancer Side Frame Plate (Right) Bill of Materials Top Level Report (see Drawing No.Bill of Materials Top Level Report (see Drawing No. Description TP-T1MA00088 Base Clamp Pipe Insert TP-T1MD00039 IOP Ctrl.Case Main Frm.Assy S-14 TP-T1MD00039-1 Ctrl.

Case TP-T1MD00039-3 I.O.P. Front Plate TP-T1MD00094 I.O.P Tube Short. For the purpose of this manual, preventative maintenance (PM) tasks are considered periodic tasks which should be performed on a daily, weekly or monthly basis. Occasionally, reprogramming will be necessary to interface auxiliary (infeed) equipment that is not manufacturer by APPI. Bill of Materials Top Level Report (see Drawing No.Bill of Materials Top Level Report (see Drawing No.When operating difficulties occur, the best procedure is to observe what is happening; then search out the causes; and effect the correction. Make only one adjustment at a time, checking the results of each adjustment. The drawing provides locations or all connection points and routings of wiring. See Dwg TC-T1000-S14. 110V Circuit Circuit drawings are provided to assist in troubleshooting the functionality of the T-1000 and also the interface signaling with auxiliary infeed equipment. Main PLC Input Description Output Description Stepper Control Stepper Motor Forward Perforation Stepper Motor Sensor Reverse Spare Perforation Activate Spare Heater Element. Pressure Out of Range MV-10 Medical Spare Val. Designed for long or short runs, the T-1000 has the capability of cycling over 100 bags per minute, faster than any operator could manually feed. The T-1000 is also fast enough to keep up with automatic infeed equipment including vibratory bowl counters, scales and infeed conveyors. Versatility: Bags virtually any product including fasteners, hardware, injection molded parts, kits, crafts, foods, medical devices and more. Reliability: Crafted from the highest quality components and materials, this bagger is built to withstand the most rigorous manufacturing environment. Machined side frames are assembled on a milled table for perfect roller alignment. Manual operation is as simple as inserting the product and pressing a foot switch. Programmable for up to thirty settings.

Quickly position the operator panel wherever you desire with a long arm extension and ball joint mounting bracket. We guarantee long life with minimal maintenance (one year parts warranty). Anti-Jam Device - Detects obstructions in the seal area, automatically reverses the pressure bar and stops the cycle operation. Excel Packaging Equipment is a family-owned and operated business in Rancho Cucamonga, California. Our inventory of packaging equipment and corresponding parts is quite diverse. We believe in servicing the equipment we sell, so clients never have to deal with another company for service. The T-100 is also fast enough to keep up with automatic infeed equipment including vibratory bowl counters, scales, and infeed conveyors. The T-1000 Advanced Poly-Bagger(TM) can reduce your packaging costs with high speeds, versatility, reliability, and simplicity.Quickly position the operator panel wherever you desire with a long arm extension and ball joint mounting bracket. The T-1000 is designed for easy movement to various production cells throughout your plant. Guaranteed long life with minimal maintenance. The T-1000 is programmed to turn off components when not in use including the touch screen, motor, air and heater bar. Now ? Designed for long or shirt runs the t-1000 has capabilities of up to 100 bags per minute (subject to product size). The t-1000 is also fast enough to keep up with automated infeed equipment including vibratory bowl counters, scales and in-feed conveyors.Programmable for up to 30 settings The t-1000 is programmed to turn off components when not in use including the touch screen panel, motor air and heater bar. The bags are loaded manually or fully automatically with input accessories. The inline accessories are operated from the machine’s touchscreen. The new T-1000S industrial machine for bag packaging (Advanced Poly-Bagger) with the stepper motor surpasses the old industrial machine T-1000 by far.

One reason for this is the interfaces within the machine.The speed of the operator also plays a role in manual operation. Therefore, only an approximate value can be given. Flexibility of use: Bags for each product or product sets. Applicable for all types of bags. Functional safety: High quality components and materials meet the strictest conditions of the production environment. Easy handling: Touch screen and dialog window, options for bags and additional equipment can be changed easily and immediately. No wonder the T-1000 is also the best-selling machine for packaging in bags. The T-1000 is also fast enough to keep up with the pace of the automatic feeder. It packs all types of parts including fasteners, hardware, injection molded parts, spare parts kits, tool parts, food, medical parts and more. Manual operation is just as easy as inserting a product and pressing a foot switch. The filler parts flow on a vibrating conveyor belt past sensors, which precisely calculate and determine whether a part is isolated and regular or not. The unit rejects hooked or irregular parts and conveys them back to the separation. Irregular parts are never allowed to be loaded. The patented Flex Feeder as an input accessory for the industrial machine T-1000 for packaging is unique and has many advantages over most known packaging systems. It counts products with a length of 3 mm to 200 mm. If you want to count and pack smaller products from 0.2 to 18 mm in length or diameter, we refer to our BM 1 counting machine It is equipped with a large hopper and a vibratory conveyor and is more suitable for fully automatic packaging. It functions as a partial counter like the standard model UC-2400 and contains a large hopper, a high-speed vibrating bowl made of stainless steel as a drive, a V-conveyor belt for separating the filler parts, an optical high-speed frame and an accumulation device for portioning. See also input accessories and TIZ printer.

The horizontal industrial machine offers countless packaging solutions for a wide variety of products that are difficult to load on the T1000 vertical industrial machine. Insert your product horizontally into the bag - either manually or automatically: the machine then takes care of the rest. It seals the bag at the charging station and unloads the filled bag on the horizontal conveyor belt. The next bag is then already blown open and positioned - ready to receive the next product. It is a chain bag on wheels. The bags are pulled into the filling position by hand, but are opened automatically and sealed automatically after parts have been filled. Forget about welding by hand, because the table machine for bag packaging T-200, which also seals automatically, increases production dramatically andPacks every type of product - from electronic components, literature, manuals, food, jewelry to hand tools! The T-200 uses our pre-opened chain bags on rolls. Simply pull the bag into the loading and sealing position so that an air stream opens and inflates the bag, throws the product to be packed into the bag, press the foot pedal or the button to seal the bag - done. It's that easy and quick. Equipped with a four-color touch screen and “pop-up” messages indicating the end of a run, as well as operation messages and error messages. Run cycle settings can be saved for immediate configuration. Changing roles takes less than a minute. The universal funnel is included in the standard equipment. Cookies helfen uns, die Benutzerfreundlichkeit unserer Website zu verbessern. Durch die weitere Nutzung der Website stimmen Sie der Verwendung zu. Weitere Informationen hierzu finden Sie in unserer Datenschutzerklarung. Einverstanden Nur notwendige Cookies. Ask us how blanket orders will save your money! It's perfectly integrated into the bagging operation with touchscreen control over the entire bagging and printing system.